Hardened PoE Switch
5-Port Hardened Gigabit PoE+ DIN-Rail Switch

5-Port Hardened Gigabit PoE+ DIN-Rail Switch


  • 4 x Gigabit PoE+ Ethernet ports, 1 x Gigabit port (RJ-45 / SFP)
  • 120 Watt power budget
  • Hardened IP30 rated metal switch
  • -40 to 75 ºC operating temperature range
  • Support Redundant Power supply
View More Details

5-Port Hardened Industrial Gigabit PoE+ DIN-Rail Switch
Higher PoE Power Output and Budget for Surveillance System
The IP120-05-SFP Industrial Gigabit PoE+ Switch provides 4-port 10/100/100Base-T copper with IEEE802.3af/at PoE+ and a 10/100/1000Base-T copper/1000Base-X SFP fiber optic combo port. PoE+ port is able to deliver up to 30W of power output and data per port over one cat.5E and cat.6 Ethernet cable, which makes IP120-05-SFP a 120W PoE output budget switch. The IP120-05-SFP is designed specifically to satisfy the high-power consuming network PD such as PTZ (Pan, Tilt & Zoom), Speed Dome network cameras, outdoor wireless access points and other PoE network devices.
Heavy Industrial Environments and Reliable Power System Design
The IP120-05-SFP is equipped with rugged metal case protection, provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb side traffic control cabinets. Designed to operate within the industrial temperature range from -40℃ to 75℃, the IP120-05-SFP is able to use 24V and 48V DC power input in transportation and industrial-level applications. To enhance the operational reliability and flexibility, the IP120-05-SFP is equipped with two DC power input connectors for redundant power supply installation. The secondary power input would begin to support whenever primary power input is detected to be malfunctioning, and the contacts for the alarm output would be opened.
The corresponding P1 or P2 LED would go out and the fault LED would light up. The IP120-05-SFP can be placed in almost any harsh electrical environments.
Flexibility Fiber-Optical Link
The Gigabit SFP slot provides fiber connectivity to support backhaul applications for carrier- class networks. The SFP Port provides flexibility when planning a network. The slot accepts any SFP fiber modules available in multiple formats.
Hardware Specifications
Interface 4 Ports 10/100/1000 BASE-T
1 10/100/1000 BASE-T or 1000 BASE SFP Combo Port
PoE Ports 1~4 port 54VDC, 30W(End-Span)
for IP120-05-SFP only
LED Indicators P1, P2, 10/100/1000M, PoE, Alarm
Alarm Contact 1A@24VDC, NO
Standards IEEE 802.3 10 Base-T Ethernet
IEEE 802.3u 100 Base-TX Ethernet
IEEE 802.3ab 1000 Base-T Gigabit Ethernet
IEEE 802.3x Flow Control
IEEE 802.3af Power over Ethernet (PoE, 15.4watts/port)
IEEE 802.3at Power over Etherent (PoE+, 30watts/port)
IEEE 802.3az Energy-Efficient Etherent
Switching Capacity 10 Gbps
MAC Address Table Size 2K
Packet Buffer Memory(bits) 1M
Jumbo Frame Size 9KB
Casing Metal, IP30
Weight 390g
Installation* DIN Rail, Wall mount
Dimensions(WxDxH) 29x110x148 mm
Power Input
No. of Power Input 2
Input Current 5.4@24VDC\2.7A@48VDC Max. (Terminal Block)
Power Consumption 4.5 watts(without PoE)
129 watts(with PoE)
Protection Reverse, Overload
PoE Power Budget(W) 120
Heat Disspation (Full load w/PoE) 534 Btu/hr
Operating Temperatuer -40℃ to 75℃(Compliance NEMA TS2)
Storage Temperatuer -40℃ to 85℃
Operating/Storage Humidity 5~95% non-condensing
Regulatory Approvals
Standard EN 55032:2012/AC:2013, Class A
CISPR 32:2012, Class A
AS/NZS CISPR 32:2013, Class A
EN 55024:2010
EN61000-4-2(ESD Srandards): Contact ±4 kV, Air Discharge: ±8 kV
EN61000-4-3(RS): 80-1000 MHz, 3V/m, 1kHz Sine Wave, 80%, AM Modulation
EN61000-4-4(EFT: AC mains power: ±1 kV, DC power: ±0.5 kV, Signal ports: ±0.5 kV
EN61000-4-6(CS): 150kHz-80MHz, 3V/m, 1kHz Sine Wave, 80%, AM Modulation
EN61000-4-8(PFMF): 50Hz, 1A/m, 1.0Min duration
Ordering Information
IP120-05-SFP Hardened 5-Ports 10/100/1000 Gigabit (4* PoE Ethernet Switch + 1*Combo 1000Base-T RJ-45/SFP ports(-40 to 75 C, IP-30)

    Contact Us